Since adding K&N’s full line of intake products on our store – Click Here For Our Full Selection – we decided to give one of them a try on our 93 LX project car. We opted for a large filter unit that replaces the stock airbox and rubber piping. The install was very straight forward and took only a few hand tools. Install took no more than 45 minutes to complete.
K&N filters are special because of their high flow characteristics and their superior engine protection. By using an oiled element they are able to trap the most dirt and dust compared to a factory paper filter or a standard replacement filter. Not only do they flow and filter better, but they are completely re-usable and will last the life of your vehicle’s engine. By using K&N’s Filter Recharge Kit you can clean and re-oil your filter back to new. They recommend you clean your filter every 20,000 miles to ensure the best protection and performance. After several years and a hundred thousand miles, the K&N filters practically pay for themselves. You actually CAN save money while gaining performance, reliability & economy…who woulda thought? Now on to the install for foxbody Mustangs:
Start off by removing the two 12mm nuts that hold the factory airbox to the engine bay.
Next, remove the clamp below the MAF sensor using a flathead screwdriver.
Once the clamp is removed, pull the factory intake assembly out of the engine bay.
Once the airbox is removed, you will need to use your 1/4″ drill bit to slightly enlarge a hole for the K&N filter’s bracket mounting position.
Once the bracket bolt fits through the hole, fit the bracket in place and tighten it. You will have to reach under the bumper to tighten the nut from the bottom of the bolt.
Once the bracket is in place and is snug, it’s time to install the new filter. Get the filter in place and make sure the threads on the end of the filter fit inside the bracket. Tighten the 11mm nut on the end of the filter.
Next tighten the hose clamp at the filter opening to ensure there will be no air leakage.
That’s it! You’re done! Below are two photos comparing the factory intake and the new K&N filter.
Shortly after the new Boss 302 was released Ford Racing Development came out with the innovative “TracKey” system. You purchase the TracKey, take your new key and your Boss 302 to Ford and they will set up a custom tune that improves throttle response, cam timing, and allows you to use a launch control system and much more. This is all pretty awesome, but where exactly is the TracKey? It’s been almost a year now and the key still isn’t available to the public. Luckily that’s all about to change. The delay was primarily brought on by California’s strict emissions laws which would make the use of the key illegal. Finally the state of California is giving the TracKey a green light, and Ford is to announce the sale of the TracKey system for sale to the entire US at SEMA 2011.
The TracKey itself will be available from your favorite Ford Racing retailer, however you will be required to take the key to your local Ford dealer along with your new Boss 302 for proper tuning. The tune effects over 600 engine parameters within the PCM (Powertrain Control Module) which increase driving pleasure, not just things you can feel, but also things you can hear. Since the release of the new Coyote 5.0 engine, tuners have realized the true potential of the new engine and the tuning possibilities. We are looking forward to some more detailed information about how real world 302’s are affected by the upcoming TracKey system, we have already seen how the launch control system works and how the tune makes for an aggressive cammed exhaust note, but considering how comprehensive this tune is supposed to be, there have got to be other improvements felt while driving the car with the special red key. Keep posted for more information in the next few months about the final release of the TracKey system!
In the mean time, check out this video courtesy of Ford Racing which shows the difference in exhaust note with the standard key and the TracKey.
Here at StangMods we’ve been a big fan of MGW shifters since they were released several years ago. Their unique design offers up one of the most comfortable and solid feeling shifters we’ve ever tested. New to the MGW line up is their silver “race” handle. This handle will fit all MGW shifters and will give the driver the shortest throw possible. The standard orange handle is still available and provides a more comfortable feel for the driver. Check out the MGW shifter with shifter gaskets when looking to upgrade the stock shifter in your Mustang.