How To Install MRT Hood Struts On 2010 & Up Ford Mustangs

MRT’s hood struts are one of the most useful mods you can do to your Ford Mustang. The stock prop rod is cheap & flimsy & doesn’t belong on a car like the Mustang. Many new luxury & performance cars come with hood strut systems from the factory, this simple mod will make opening your hood easier and quicker, a useful tool for those who work on their Mustangs on a regular basis. You can find this black MRT Hood Strut Kit on StangMods by clicking the following link: MRT Black Hood Strut Kit

For this install you will need a couple of tools. They are:  a 10mm socket wrench, razor cutter or scissors, flat head screwdriver, extra set of hands to help support the hood when adding the strut brackets.

Start by locating the fender bolt closest to the hood of the car, remove this 10mm bolt, place the lower bracket there & tighten it down. The RH side is the passenger side, LH is the drivers side. Each bracket in the kit is engraved with either RH or LH.

IMG_1949

IMG_1950

After the lower brackets are in place it’s time to install the upper brackets. You may want to grab a friend to help with this step. Remove the upper 10mm bolt and LOOSTEN the lower one just enough to slide the braket under the head of the lower bolt. Reinstall the upper bolt once the lower part of the bracket is fastened by the lower bolt.

IMG_1942

IMG_1952

IMG_1954

Once the brackets on both sides of the hood/vehicle are installed and tightened, install the struts! You can now ditch the prop rod for good, you can even unbolt it’s bracket & throw it in the trash, up to you!

The steps above complete the install process on 05-09 Mustangs. If you have a 2010 and newer model you’ll need to modify the sound tube located on the driver’s side. This is required to give the hood strut clearance.

Start by removing the lower rubber bushing under the plastic bracket. There is a small metal guide for the bolt pressed through this bushing, you can remove it with a flathead screwdriver Do not throw this away as it will be reused. Once the rubber bracket has been removed, cut about half an inch out of the center of the rubber bushing as marked by the red lines in the photo below.

IMG_1957

After you’ve cut the bushing install everything backwards like shown below. The U clip that the bolt originally threaded into must be installed on the bottom of all of this.

IMG_1959

Once everything is lined up, bolt it down like shown below. All done!

IMG_1961

Now you have an attractive, useful mod that’ll give you more clearance while providing a nice visual upgrade . For more information on MRT’s Hood Strut Kits, follow this link: http://www.stangmods.com/MRT-Hood-Struts-05-13-Mustangs-p/00109.htm

Installing Webelectric’s 05′-09′ Mustang Plug-In Sequential Turn Signals

In this writeup we will go over the installation process of our very popular 2005-2009 Mustang Plug in Sequntial kit. Installation is very simple and requires only a couple of basic tools.

Tools Required:

  • 7/16″ Deep Socket
  • Flat head screw driver

First you’ll want to remove the black trim panel from inside the trunk area. Start by removing the twist off screw and push pin as circled below. Use the flat head screw driver to gently pry out the push pin. Repeat on the other side of the vehicle.

Next use your flat head screw driver and remove the two push pins as shown below. Again, gently pry out the pins to avoid any damage.

Take your 7/16 deep socket and remove the three nuts located on the inside of the trunk as shown below. These nuts hold the tail lamp onto the vehicle.

Once you’ve removed all three nuts, you are ready to remove the tail lamp and harness from the vehicle. Depress the tab on the grey harness plug and separate the connectors.

Now, gently pull the tail lamp away from the body of the vehicle and work the harness grommet out of its location using the flat head screwdriver as shown below. Once its free, pull the entire tail lamp and harness completely out.

With the tail lamp out from the vehicle, place it on a flat work bench and begin removing the light sockets by turning them counter-clockwise. You must also remove the socket for the reverse lamp. Finally, the harness is attached to the tail lamp with a white push pin. Remove it gently and free the harness from the tail light.

At this point we are almost done with the first side. Pull the bulbs out of the OEM harness and plug them back into the sequential harness. Before you re-install the new sequential harness, it is important to note the correct position. Each socket is pre-labeled with the numbers 1,2,3. Socket 1 should be installed in the inner most lens, socket 2 in the middle lens, and socket 3 on the outermost lens.

The orientation for the driver’s side tail lamp is shown below:

The orientation for the passenger side tail lamp is shown below:

The new sequential harness contains the white push pin. Remember to place it back in to secure the harness to the tail lamp.

To finish up the installation, re-route the harness with the grey connector through the body of the vehicle and plug it back in. Then, secure the black grommet and re-install the tail lamp. Re-attach the (3) bolts holding the tail lamp to the vehicle. Once you have completed the installation on the opposite side, place the black trim piece in place and re-attach the plastic push pins to complete your installation.

Now you can dazzle everyone when you flick your signals on with this unique product from StangMods.com