Installing StangMods 99-04 Vinyl Tail Light Decals

Mustang Tail Light Decal Installation (Flamed, Outline & Honeycomb Kits)

Tools Required:

  • Squeeggee
  • Spray bottle
  • Liquid soap
  • Terry cloth or towel

Use rubbing alcohol to wash all dirt and road grime from the surface of your tail lights.

Mix your soapy water solution by adding a few drops of liquid soap to warm water in a spray bottle.

Generously spray the solution over the lens you are working on. Then remove the vinyl decal from the paper backing and apply it to the lens.

While the solution is still saturating the tail light lens, align the decal for a correct fitment and use your squeeggee to remove any excess solution from underneath the decal. Start from the center and move your way out.

Wait a few minutes, depending on the temperature, and then try to remove the transfer tape (top protective paper) from the vinyl. If the paper comes off and the vinyl stays in place, then you are good to go and you can move on to the next one. If the vinyl comes off, rather than staying on the car then use your squeege to apply the decal over the lens again.

Finish up by wiping off any excess solution from the body of your Stang.

Visit StangMods for more Mustang vinyl decals

Installing StangMods’ Vinyl Lower Bumper Insert for 99-04

 

Mustang Vinyl Lower Rear Bumper Insert Installation

 Tools Required:

  • Squeeggee
  • Spray bottle
  • Liquid soap
  • Terry cloth or towel

First start off by making your soapy solution by combining three to four drops of dishwashing detergent with warm water

Next, you’ll want to thouroughly clean and prep the area for instalaltion. Use alcohol to clean any dirt or debris from the lower bumper area.

Once everything is nice and dry, you’ll now be ready for installation. Peel off the backing of the vinyl overlay. Be careful not to let it touch any surface other than the vehicle.

Spray the soapy solution over the entire lower bumper area.

Align the vinyl in place and use a squeegee to apply it to the vehicle.  Work from the center of the vinyl to the edges, slowly pushing any air bubbles and excess solution out from under the decal. It may take a few minutes until the vinyl begins to adhere to the vehicle.

Finish up by wiping off any excess solution from the body of your Stang.

Visit StangMods for more vinyl Mustang decals.

Installing Vinyl Mustang Bumper Inserts on 99-04 Mustangs

Installing Mustang vinyl bumper inserts is probably one of the simplest modifications that can be done to your 99-04 Mustang. We go over the rather quick process in this installation write-up.

Tools Required:

  • Spray Bottle
  • A couple of drops of liquid soap
  • Q Tip
  • Hair dryer or heat gun (optional)

You first want to make sure the letter area on your rear bumper is completely clean and dry. This is absolutely important to ensure the letters adhere to the bumper properly. After this is done, you’ll want to mix a warm water and liquid soap solution and put it in a spray bottle. Any liquid soap will work.

Next, take your water/soap solution and spray down the letter area on your rear bumper. It is better to work with one letter at a time. Here we are starting with the M.

Once the area is wet, take the vinyl bumper letter and peel off the thicker paper backing as shown below.

Now, line up the vinyl letter with the indentation on the bumper. Take your time and be patient as you want to make sure the letters are lined up correctly.

Once the letter is lined up with the indentation in the bumper, take your q-tip and begin smoothing out the letter onto the bumper.  Work from the center towards the sides. Try to get as much as the liquid solution out from the letter.

It is important to note that if you are working in temperatures below 60 degrees, you may want to use a hair dryer or heat gun to help warm up the vinyl. This makes it easier to adhere to the bumper.

Once the letter is firmly in place, you can peel off the transfer tape. Start peeling the paper away slowly. If the vinyl letter stays in place on the bumper then you can remove the rest of the transfer tape.

Repeat the above process for the rest of the letters. Take your time with the “G” as it is more difficult to line up correctly. After your done, you’ll be left with this:

This write up has been sponsored by: StangMods.com

How To Install Map Light/Dome Bulbs in 2005-2012 Mustangs

This installment of writeups goes over the installation of LED dome light bulbs on the 2005-2009 Mustangs.

Tools Required:

  • None

You first want to remove the cover to access the dome bulbs. Simply grasp the cover firmly and pull down.

Next, use your thumb or a thin point and depress the tab holding the harness to the grey connector. Once you release the tab, gently pull the dome bulb cover away.

Take the assembly to a clean work area to prepare the installation of the new bulbs. There are two separate bulbs in the housing. Remove the bulbs by pulling them straight out.

Now, remove the stock bulbs and re-install your new LED bulbs. Once this is done, you are now ready to re-install the dome housing back into the vehicle. Remember to plug the grey connector back in the harness. Finally, line up the tabs on the dome housing as shown below.

Check to make sure your lights work and that completes the installation. Now you have a brighter light to help make things easier to see inside your Stang!

You can find our LED map light/dome bulbs by clicking the following links: White LED Map/Dome BulbsBlue LED Map/Dome Bulbs

Installing Chrome/Amber Bulbs In 1999-2004 Mustangs

In this write up, we go over the installation process of the chrome/amber turn signal bulbs. Installation is very simple and no tools are required. These bulbs complement clear corner headlamps and turn signals very well. We installed the bulbs in our smoked clear corner headlamps for the 99-04 Mustang. The bulb will fit any application using a 3157 bulb type.

Tools Required:

  • None

First remove the two headlamp pins that secure the headlamp to the vehicle. Simply place your finger under the tab as shown below and pull up. There are two pins per headlamp. These are the only items securing the headlamp to the vehicle.

Once the pins are removed, gently slide the headlamps away from the body of the vehicle. It may take some effort, but eventually they will work free. Once you have some space, unplug the wiring harness from the headlamp bulb. Simply pull up on the tabs and gently release the harness.

Next, remove the wiring harness connected to the turn signal bulb. Depress the sides of the harness and gently pull it off the turn signal bulb. The picture below shows the harness removed from the bulb.

Turn the bulb counter clock-wise to remove it from the headlamp. The picture below shows the bulb partially removed from the housing.

The picture below shows the stock turn signal bulb located in its base. Gently pull the bulb out of the base to prepare for re-installation of the new turn signal bulb.

Take the new chrome/amber bulb and re-install it in the adapter. Be careful not to touch the bulb with your bare hands or fingertips. The new chrome/amber bulb installed is shown below.

Finally, reverse steps one through four and your installation is complete.

The new chrome/amber turn signal bulb shown in action below.

You can find our chrome/amber replacement bulbs here – http://www.stangmods.com/Chrome-Amber-3157-Bulbs-p/00729.htm

Installing StangMods’ Mach 1 Grill Delete For 99-04 Mustangs

In this write-up we will go over the installation of our three piece Mach 1 Grille Delete Package. Our kit uses Ford OEM parts for great fit and finish as well as long term durability. This is one of our most popular sellers along with the Mach 1 lip spoiler. You can find our grill delete packages here: StangMods Grill Delete Packages

Tools Required:

  • 7MM Socket
  • Phillips Head Screwdriver
  • Flat Head Screwdriver

First start off by removing the four plastic push screws from the top portion of the stock grille. After removing these four screws, you will see two more push pin screws on each side. (Do not break these as they will be reused). The easiest method is to use a flat head screw driver to gently pry them up from underneath.

Now you are going to remove the four bolts holding the factory grill in place. They are a little awkward to get to so we recommend pulling the stock grill forward enough so you can reach down and remove the 7MM bolts with a socket.

Take the top center section and install it using the two push pins at the lower section of the grille delete.  Next, you will install the “U” shaped section. Reinstall it using the two push pins that were holding the stock grill on at the top. Make sure the four bottom posts are inserted into the bottom portion of the bumper. Remove the backing off of the 3M tape and push securely against the bumper to ensure a flush fit.

Finally, mount the running pony with the two new bolts using the phillips head screwdriver. You are now done with the installation.

Replacing Your 05-09 Mustang’s Rear License Plate Bulb

In this writeup we go over the installation of a license plate bulb on any 2005-2009 Ford Mustang. StangMods carries not only standard halogen replacement bulbs but also high output LED bulbs in HID white and blue. You can find our selection of exterior bulbs here – http://www.stangmods.com/Mustang-Exterior-Bulbs-from-StangMods-com-s/106.htm

The only tool required for this install is a flat head screwdriver. This tool will be used to remove the fasteners holding the license plate bulb cover in place. First locate the two push pins holding the bulb cover in place. Using your flat head screwdriver, gently pull them out as shown below.

Once the pins are removed, grasp the cover as shown below and gently pull down. Do not use much force as the cover will be held to the vehicle with a wiring harness.

 

The stock bulb is attached to the grey harness. Give it a half turn counter-clockwise to release the harness and bulb from the cover.

To complete the installation, remove the stock bulb and re-install the new LED into the harness and then back into the cover. Finish up by re-attaching the two push pins you removed in step 1. Thats all there is to it. This rather simple mod really livens up an otherwise overlooked area of your ride!

You can purchase your LED license plate bulbs and replacement bulbs from StangMods.com