Installing Vinyl Rear Decklid Panels on 99-04 Mustangs

Our popular 99-04 vinyl decklid panel is a fast and affordable way to give your Mustang an aggressive look & stand out from the crowd. This automotive grade (wont leave nasty residue) adhesive vinyl covering comes in either gloss black, carbon fiber or matte black. All of our vinyl overlays come with a free squeegee to help with the install. These decklid overlays are a very popular seller and have been a huge success over the years for V6, GT, and Cobras alike. Check out our full line of dress-up vinyl overlays here: http://www.stangmods.com/Mustang-Graphics-Vinyl-s/224.htm

Tools Required:

  • Squeegee (Included)
  • Spray bottle
  • Liquid soap
  • Terry cloth or towel

 

First remove any and all emblems including the Ford Oval emblem and any other emblem that your   specific model came with. Also remove your license plate.

Next, use rubbing alcohol to wash all wax and dirt from the surface where the decklid panel will be installed.

Make a soapy solution of by combining three to four drops of dish washing detergent with warm water.

Spray the solution over the decklid area where the new vinyl overlay will be installed.

Once the area is saturated, start with one section at a time and peel off the paper backing material from the black vinyl.

Align the vinyl in place and use a squeegee to apply it to the vehicle.  Work from the center of the vinyl to the edges, slowly pushing any air bubbles and excess solution out from under the decal. Please be patient with this procedure. It may take several minutes for the vinyl to finally adhere. Repeat this procedure for the other two sections and your done!

Use your terry cloth towel to wipe off any excess solution from your Stang.

Visit StangMods to purchase your Vinyl Mustang Decklid Trim Panel and other Mustang vinyl decals

How To Install Map Light/Dome Bulbs in 2005-2012 Mustangs

This installment of writeups goes over the installation of LED dome light bulbs on the 2005-2009 Mustangs.

Tools Required:

  • None

You first want to remove the cover to access the dome bulbs. Simply grasp the cover firmly and pull down.

Next, use your thumb or a thin point and depress the tab holding the harness to the grey connector. Once you release the tab, gently pull the dome bulb cover away.

Take the assembly to a clean work area to prepare the installation of the new bulbs. There are two separate bulbs in the housing. Remove the bulbs by pulling them straight out.

Now, remove the stock bulbs and re-install your new LED bulbs. Once this is done, you are now ready to re-install the dome housing back into the vehicle. Remember to plug the grey connector back in the harness. Finally, line up the tabs on the dome housing as shown below.

Check to make sure your lights work and that completes the installation. Now you have a brighter light to help make things easier to see inside your Stang!

You can find our LED map light/dome bulbs by clicking the following links: White LED Map/Dome BulbsBlue LED Map/Dome Bulbs

Installing 05-09 Mustang Turn Signal Bulbs & Lenses

In this edition of writeups, we go over the installation process of adding front turn signals to your 2005-2009 Mustang. Installation can be done without even lifting the car in the air.

  • Tools Required:
    Phillips Screwdriver

If you begin with the driver’s side, you’ll want to turn the wheel all the way over to the passenger side to gain access to the screws holding the inner fenderwell on. Remove them using a phillips head screwdriver along with the one push pin.

Once all three screws are removed, you can peel back the inner fenderwell and gain access to the turn signal lens behind the bumper cover. Now you’ll work on removing the stock turn signal lens. There are two white pins holding the turn signal to the bumper cover. Squeeze one pin at a time and gently pull the lens away to release it from the bumper.

Now, you’ll want to remove the stock bulbs from the turn signal lens before completely removing it from the vehicle. There are two separate bulbs in the lens. (3157 and 194 bulb) Grasp each bulb and turn it counter-clockwise to free it from the housing. The lens should be free now. Remove it from underneath the bumper. It helps to have an extra set of hands here

We are now ready to re-install the new turn signal lens. You first want to find the tab behind the bumper cover. This will help you guide the new turn signal lens into place. The tab is shown below.

Slide the new lens in through the opening in the fenderwell. Align the tab on the new lens with the slot on the bumper cover as shown below.

Secure the other end of the lens with the white pins as shown below.

One of the last steps is to install the new 3157 and 194 Chrome-Amber Bulbs. Using latex gloves, remove the stock bulbs and re-install the chrome amber ones. Then place them in the housing and turn them clock wise to secure them in the new lens. It is important to not touch the glass portion of the bulb with your exposed fingers. The oils from your skin can prematurely wear out the bulb. Once your bulbs are in, turn on your turn signals to ensure they work.

Finally, re-install the inner fenderwell screws to complete your installation. Now you can enjoy the clear look while staying DOT legal. The different turn signal lens and bulb packages can be found on our site here: http://www.stangmods.com/Mustang-Clear-Turn-Signal-Lenses-Side-Markers-s/157.htm

Installing StangMods’ Mach 1 Grill Delete For 99-04 Mustangs

In this write-up we will go over the installation of our three piece Mach 1 Grille Delete Package. Our kit uses Ford OEM parts for great fit and finish as well as long term durability. This is one of our most popular sellers along with the Mach 1 lip spoiler. You can find our grill delete packages here: StangMods Grill Delete Packages

Tools Required:

  • 7MM Socket
  • Phillips Head Screwdriver
  • Flat Head Screwdriver

First start off by removing the four plastic push screws from the top portion of the stock grille. After removing these four screws, you will see two more push pin screws on each side. (Do not break these as they will be reused). The easiest method is to use a flat head screw driver to gently pry them up from underneath.

Now you are going to remove the four bolts holding the factory grill in place. They are a little awkward to get to so we recommend pulling the stock grill forward enough so you can reach down and remove the 7MM bolts with a socket.

Take the top center section and install it using the two push pins at the lower section of the grille delete.  Next, you will install the “U” shaped section. Reinstall it using the two push pins that were holding the stock grill on at the top. Make sure the four bottom posts are inserted into the bottom portion of the bumper. Remove the backing off of the 3M tape and push securely against the bumper to ensure a flush fit.

Finally, mount the running pony with the two new bolts using the phillips head screwdriver. You are now done with the installation.

Installing The Mach 1 Chin Spoiler On Your 1999-2004 Mustang

Our latest write-up goes over the process of installing a Mach 1 style chin spoiler on a 1999-2004 Mustang. StangMods carries high quality ABS plastic Mach 1 style lip spoilers with an OEM style textured finish. Not the glossy finish many aftermarket companies sell. Each of our chin spoiler kits comes included with push pin fasteners for a tight fit. This chin spoiler will give the front of your 99-04 Mustang a clean yet sporty look. You can find our chin spoilers for 99-04 here – http://www.stangmods.com/Mustang-Chin-Spoiler-for-99-04-p/00084.htm and the same chin spoiler for 96-98 Mustangs here – http://www.stangmods.com/Mustang-Chin-Spoiler-for-94-98-Mustangs-p/00542.htm

Tools Required:

  • Duct Tape
  • Push Pin Fasteners
  • Drill
  • 1/4″ Drill Bit

First start off by securing the vehicle on a level surface. Make sure the car is in gear and the parking brake is engaged.

Raise the front of the car so that you may have adequate space to work underneath the front bumper.

Mock fit the chin spoiler to the front bumper. It is easier if two people are handling the chin spoiler.

When you get the spoiler positioned to your liking, use duct tape to secure it to the bumper. (Tape will be removed later)

Drill ¼” holes into the bottom of the front bumper at each Chin Spoiler screw location.

Finally, insert pushpin fasteners into the holes on the bumper to secure the chin spoiler.

The last step is to remove the duct tape you used earlier to secure the chin spoiler to the bumper.

This completes the installation process.

 

Installing Bixenon HIDs in 99-04 Ford Mustangs

In this write-up we will be going over the installation of StangMods’ bixenon HID conversion kit for 1999-2004 Ford Mustangs. This kit will increase light output and offer a whiter light for added style.

Tools Required:

  • 8 MM or 5/16 Socket

First you’ll want to remove your stock headlamps from the vehicle. This process can be found through this link.  Once your headlamp lenses have been removed, lay your wiring harness along the battery area underneath the hood as shown below.

Run the longer end of the harness over to the passenger side area. It is not important to tuck it away neatlly at this moment.

Now move back over to the driver’s side. There are two O ring connections that need to be made. One is a power (red wire) and ground (black wire). Connect the red O ring terminal to the positive side of the battery. Next, connect the black O ring terminal to a good ground source. We chose the bolt on the inner fenderwell as shown below.

You’ll now be left with three connections to be made on the driver’s side. Tuck them down next to the battery and out through the opening behind the headlamp as shown below.

Route the passenger side harness as shown below.

You can connect the gound O ring for the passenger side to the bolt for the hood prop rod.

Now we will be preparing the bulb for installation. The bixenon bulb has a removable base that must be removed before installing it in the headlamp housing. Simply twist the base counter clockwise and it will be removed. Once the base is removed, place the bulb through the plastic locking collar as shown below.

You can now reattach the base and install the bulb in the housing as shown below.

The final step is to re-attach the plastic locking collar to secure the bixenon bulb in the housing as shown below.

There are three remaining connections to be made on the passenger side. They are all all a simple plug in procedure. Simply match up the corresponding plugs. The final step on the passenger side is to mount your ballast. We chose to mount it on the inner fender as shown below.

At this point, you can zip tie all of the passenger side connections in place. We chose to zip tie the harness directly underneath the radiator shroud as shown below.

 

Move over to the driver’s side to complete the installation. Plug the stock harness into the blue plug on the driver’s side as shown below. Keep in mind that the stock harness plug on the passenger side is not used.

Tuck the harness connection back through the opening as shown below. You can also tuck your driver’s side ballast back through this opening. It is not necessary to use mounting brackets to secure it as there is limited space for the ballast to move around.

Finally, complete your plug in connections as you did on the passenger side and tuck away the harness around the battery as shown below. Once you have the wires in their desired location, you can use zipties to secure them to existing OEM wires.

All thats left is to re-install your driver’s side headlamp and check the HIDs to ensure they come on.

You can find our selection of Mustang HID conversion kits here: http://www.stangmods.com/Mustang-HID-Lighting-s/61.htm