K&N Performance Filters – Installing One In Your Mustang

Since adding K&N’s full line of intake products on our store – Click Here For Our Full Selection – we decided to give one of them a try on our 93 LX project car. We opted for a large filter unit that replaces the stock airbox and rubber piping. The install was very straight forward and took only a few hand tools. Install took no more than 45 minutes to complete.

K&N filters are special because of their high flow characteristics and their superior engine protection. By using an oiled element they are able to trap the most dirt and dust compared to a factory paper filter or a standard replacement filter. Not only do they flow and filter better, but they are completely re-usable and will last the life of your vehicle’s engine. By using K&N’s Filter Recharge Kit you can clean and re-oil your filter back to new. They recommend you clean your filter every 20,000 miles to ensure the best protection and performance. After several years and a hundred thousand miles, the K&N filters practically pay for themselves. You actually CAN save money while gaining performance, reliability & economy…who woulda thought? Now on to the install for foxbody Mustangs:
Tools Needed:

1/4″ Drill

12mm socket

11mm wrench

Flathead screwdriver

Start off by removing the two 12mm nuts that hold the factory airbox to the engine bay.

Next, remove the clamp below the MAF sensor using a flathead screwdriver.

Once the clamp is removed, pull the factory intake assembly out of the engine bay.

Once the airbox is removed, you will need to use your 1/4″ drill bit to slightly enlarge a hole for the K&N filter’s bracket mounting position.

Once the bracket bolt fits through the hole, fit the bracket in place and tighten it. You will have to reach under the bumper to tighten the nut from the bottom of the bolt.

Once the bracket is in place and is snug, it’s time to install the new filter. Get the filter in place and make sure the threads on the end of the filter fit inside the bracket. Tighten the 11mm nut on the end of the filter.

Next tighten the hose clamp at the filter opening to ensure there will be no air leakage.

That’s it! You’re done! Below are two photos comparing the factory intake and the new K&N filter.

Installing The Boss 302 Alcantara Steering Wheel In 2010-2013 Mustangs

If you are looking for a change from the factory cheap rubber or leatherette steering wheel we have your solution. For under $300 you can own a real Boss 302 steering wheel with the plush alcantara covering and install it in any 2010-2013 Mustang! This is a real Ford part, the same wheel you will find on all 302s that roll off the production line. The install is pretty straight forward and takes about an hour and a half, uses simple tools and will make your Mustang feel like a race car every time you put your hands on the wheel.

Tools Required:

24mm socket

8mm socket

Socket extension

Optional Tools (If swapping buttons)

Torx 20

Torx 27

Start by removing the negative terminal on your Mustang’s battery. Give the car 20 minutes to fully drain the charge to ensure it’s safe to remove the airbag from the car. It’s unlikely the airbag could deploy, but it’s one of those situations where it’s way better to be safe than sorry.

Next, remove the two caps covering the 8mm bolts that hold the airbag unit in place.

Remove the 8mm bolts on either side of the wheel using a socket and ratcheting wrench.

After removing both 8mm bolts, carefully and slowly pull the center airbag unit straight out, be careful not to tug on the airbag’s harness when removing it.

Disconnect the large black plug (steering wheel harness) next to the yellow airbag wire.

Next, remove the clips carefully on the back of the airbag unit itself. The plugs are color coded to match their clips, one grey and one black.

Set the airbag unit aside in a safe place. Now that everything is disconnected, you can remove the 24mm bolt in the center of the wheel that holds the old wheel in place.

Once this bolt is removed, the wheel will come off, be sure to thread the wiring through the wheel when removing it to ensure you don’t break any clips or wires.

Now that the wheel is removed, check out these comparison photos of the factory wheel vs the Boss 302 wheel.

If your Mustang is a 2013 or comes with sync, you can swap the buttons from your factory wheel onto the new alcantara wheel so you don’t lose any functionality. You will have to remove the buttons and the wiring harness from the old wheel and swap it to the new wheel. To view that write up, follow this link:

How To Swap Sync Buttons To Your New Boss 302 Steering Wheel

Now all that’s left is to reinstall the new wheel in the same manner you removed the factory one. Start by bolting the wheel in with the 24mm bolt. Ford says to torque this bolt to no more than 45ft lbs, do not over tighten this bolt or it could strip out. Make sure to line up the wiring harness plugs through the top hole and pull the wires through as shown below.

Plug in the main black plug for the wheel harness and put the airbag clips in their respectable plugs. It’s very important to ensure you put the grey clip in the grey plug and the black clip[ in the black plug.

After everything is hooked up wiring wise, carefully reinstall the airbag unit in the wheel. Make sure the unit is lined up with the side bolt holes and reinstall the two 8mm bolts on either side. After making sure the bolts are snug (don’t over tighten) replace the bolt cover caps and you’re ready to go!

Now it’s time to enjoy your new Boss steering wheel! Reconnect the battery once you’ve double-checked all the wiring and bolts. Make sure all your buttons are working properly. Enjoy!

To find this wheel for sale on our online store, click the following link: Boss 302 Alcantara Steering Wheel for 10-13 Ford Mustangs

Boss 302 TracKey System

Shortly after the new Boss 302 was released Ford Racing Development came out with the innovative “TracKey” system. You purchase the TracKey, take your new key and your Boss 302 to Ford and they will set up a custom tune that improves throttle response, cam timing, and allows you to use a launch control system and much more. This is all pretty awesome, but where exactly is the TracKey? It’s been almost a year now and the key still isn’t available to the public. Luckily that’s all about to change. The delay was primarily brought on by California’s strict emissions laws which would make the use of the key illegal. Finally the state of California is giving the TracKey a green light, and Ford is to announce the sale of the TracKey system for sale to the entire US at SEMA 2011.

The TracKey itself will be available from your favorite Ford Racing retailer, however you will be required to take the key to your local Ford dealer along with your new Boss 302 for proper tuning. The tune effects over 600 engine parameters within the PCM (Powertrain Control Module) which increase driving pleasure, not just things you can feel, but also things you can hear. Since the release of the new Coyote 5.0 engine, tuners have realized the true potential of the new engine and the tuning possibilities. We are looking forward to some more detailed information about how real world 302′s are affected by the upcoming TracKey system, we have already seen how the launch control system works and how the tune makes for an aggressive cammed exhaust note, but considering how comprehensive this tune is supposed to be, there have got to be other improvements felt while driving the car with the special red key. Keep posted for more information in the next few months about the final release of the TracKey system!

In the mean time, check out this video courtesy of Ford Racing which shows the difference in exhaust note with the standard key and the TracKey.

Facebook Fan Page Store

Over the weekend we will be launching our Facebook Fan Page Store! Here you will be able to find a few of our most popular items at discount compared to on our website. Over the years we have gotten great feedback and support from our customers on Facebook, so to give back we are excited to offer these discounts to anyone who visits our Fan Page. Better yet, all of these items are In Stock and Ready To Ship!

To find the store on our Fan Page, click the “Social Store” tab on the left side of the page under our profile photo. Click Here to check it out now!

BBK Parts Now Available!

We are in the process of adding BBK’s comprehensive line of Mustang performance parts to our online store. BBK has been in the Mustang industry for over 20 years and manufactures in-house many exhaust systems, intakes, throttle bodies, and much more. All their parts are manufactured in the USA and are tested on cars to ensure maximum performance potential. Affordable, high quality, and durable for long lasting use on street or race applications. Check out our line of BBK parts in our BBK category.

View Our BBK Selection